Yamaha Digital Mixing Console
Yamaha Digital Mixing Console
Yamaha TF3 - Digital Mixing Console
The Yamaha TF3 is a rack-mountable digital audio mixing console that features a touchscreen display, 25 motorized faders, and is expandable up to 48 input channels by adding the optional Tio1608-D I/O rack. Ideal for a multitude of live sound reinforcement scenarios, the TF3 can also be used for live recording, offering 34 x 34 channel digital recording and playback via USB 2.0 using a computer and your preferred DAW software, and 2 x 2 channel recording and playback using any USB storage device.
| Yamaha TF3 Specs |
|---|
| General |
|---|
| Faders |
25 |
| Mixer |
Input Channels: 48 (40 mono + 2 stereo + 2 return)
Aux Buses: 20 (8 mono + 6 stereo)
Stereo Buses: 1
Sub Buses: 1
Input Channel Functions: 8 DCA Groups |
| I/O |
Inputs: 24 mic/line (XLR/TRS combo) + 2 stereo line (RCA pin)
Outputs: 16 (XLR)
Expansion Slots: 1 |
| DSP |
8 effects + 10 GEQ |
| USB |
34 x 34 USB audio interface, 2-track recording via USB storage device |
| Sampling Frequency |
48 kHz, internal |
| Signal Delay |
Less than 2.6 ms, INPUT to OMNI OUT, Fs=48 kHz |
| Faders |
100 mm motorized, resolution = 10-bit, +10 to -138 dB, -? dB all faders |
| Total Harmonic Distortion |
Less than 0.05% 20 Hz - 20 kHz @ +4 dBu into 600 ohms, INPUT to OMNI OUT, input gain = min. (measured with a -18 dB/octave filter @ 80 kHz) |
| Frequency Response |
+0.5, -1.5 dB 20 Hz - 20 kHz, refer to +4 dBu output @ 1 kHz, INPUT to OMNI OUT |
| Dynamic Range |
110 dB typ., DA converter, 107 dB typ., INPUT to OMNI OUT, input gain = min |
| Noise |
Equivalent Input Noise:-128 dBu typ., input gain = max. (measured with an A-weight filter)
Residual output noise:-85 dBu, ST master off (measured with an A-weight filter) |
| Crosstalk |
-100 dB (measured with a -30 dB/octave filter @ 22 kHz), adjacent INPUT/OMNI OUT channels, input gain = min |
| Power Requirements |
100 - 240 V 50/60 Hz |
| Power Consumption |
110 W |
| Analog Inputs |
Input Terminals: INPUT 1-24, ST IN 1,2
GAIN: -6 dB / +66 dB (INPUT 1-24)
Load Impedance: 7.5 kOhms (INPUT 1-24); 10 kOhms (ST IN 1,2)
For Use With Nominal: 50 - 600 ohm mics or 600 ohm lines (INPUT 1-24); 600 ohm lines (ST IN 1,2)
Sensitivity: -82 dBu (61.6 V), -10 dBu (245 mV) (INPUT 1-24); -30 dBV (31.6 V) (ST IN 1,2)
Nominal: -62 dBu (0.616 mV), +10 dBu (2.45 V) (INPUT 1-24); -10 dBV (316 mV) (INPUT 1-24)
Max. Before Clip: -42 dBu (6.16 mV), +30 dBu (24.5 V) (INPUT 1-24); +10 dBV (3.16 V) (ST IN 1,2)
Connector: Combo Jack (XLR-3-31 type or TRS phone) balanced (INPUT 1-24); RCA pin jack unbalanced (ST IN 1,2) |
| Analog Outputs |
Output Terminals: OMNI OUT 1-16, PHONES
Source Impedance: 75 ohms (OMNI OUT 1-16); 100 ohms (PHONES)
For Use With Nominal: 600 ohm lines (OMNI OUT 1-16); 40 ohms (PHONES)
GAIN SW: +24 dBu position (default) (OMNI OUT 1-16)
Nominal Output Level: +4 dBu (1.23 V) (OMNI OUT 1-16); 3 mW (PHONES)
Max. Output Level Before Clip: +24 dBu (12.3 V) (OMNI OUT 1-16); 75 mW (PHONES)
Connector: XLR-3-32 type balanced (OMNI OUT 1-16); stereo phone jack (TRS) unbalanced (PHONES) |
| Digital Input/Output |
Terminals: USB (TO HOST), iPad
Format: USB
Data length 24-bit (USB TO HOST)
Audio: 34 ch input / 34 ch output, PCM (USB TO HOST); Playback: MP3 or WAV file data / Record: WAV file data (iPad)
Connector: USB (B type) (USB TO HOST); USB (A type) (iPad) |
| Control I/O |
Terminals: NETWORK, FOOT SW
Format:IEEE802.3 (NETWORK)
Level: 10BASE-T/100Base-TX (NETWORK)
Connector: RJ-45 (NETWORK); TS Phone (FOOT SW ) |
| Packaging Info |
|---|
| Dimensions |
28.2 x 8.9 x 23.6" (716 x 225 x 599 mm) |
| Net Weight |
37.5 lb (7.0 kg) |
